type
VB-1½ -
1½" Discharge Sump Pumps
Bulletin
203A
List
Prices
BASIC SINGLE UNIT includes one pump (for 2-ft. thru 4'6" pit depth)
plus one motor plus one float switch (float switch is motor mounted for 1-ph.
units and suspension plate mounted for 3-ph. units).
BASIC DUPLEX UNIT includes two of the components described
above.
NOTE: All prices are F.O.B. Brooklyn, N.Y. except for cast iron basins and
fiberglass basins, which are F.O.B. Indiana.
| |
List
Prices |
Ship'g
Weights |
| Unit
No. |
HP |
RPM |
1-Ph.
Single |
1-Ph
Duplex |
3-Ph.
Single |
3-Ph.
Duplex |
Single |
Duplex |
| VB-1½-1/4-4 |
1/4 |
1750 |
$3159 |
6318 |
3285 |
6570 |
160# |
320# |
| VB-1½-1/3-4 |
1/3 |
1750 |
3189 |
6378 |
3297 |
6594 |
160 |
320 |
| VB-1½-1/2-4 |
1/2 |
1750 |
3435 |
6870 |
3327 |
6654 |
160 |
320 |
OVERLOAD PROTECTION:
Single phase motors have built-in overload protection. Three phase motors do
not have such protection and require a magnetic starter.
NON-STANDARD SUSPENSION PLATE:
To substitute a 20" dia. suspension plate for the standard 14" dia.
suspension plate, add per pump --- $228
PIT DEPTH ADDITIONS:
When the pit in which the VB-1-1/2 pumps are to be installed is deeper than
the standard 4'6" depth, make the following list price and weight
additions.
| Pit Depth |
No. of Interm. Bearings Per Pump |
No. of Sus. Leg sections Per Pump |
List Add. Single |
Wgt. Add. Single |
List Add. Duplex |
Wgt. Add. Duplex |
| 2' thru 4'6" |
0 |
1 |
std. |
std. |
std. |
std. |
| 5' thru 7' |
1 |
2 |
$705 |
50# |
$1410 |
100# |
| 7'6" thru 10' |
2 |
3 |
1410 |
100 |
2820 |
200 |
ALL-BRONZE CONSTRUCTION:
To price VB-1/ pumps of all-bronze construction (all bronze components below
the suspension plate, including leg and discharge pipe), price the basic
4'6" unit, then make the required pit depth addition, and then make the
all-bronze addition shown below.
| Pit Depth |
Single |
Duplex |
| 2' thru 4'6" |
$1143 |
$2286 |
| 5' thru 7' |
2016 |
4032 |
| 7'6" thru 10' |
2871 |
5742 |
FREE STANDING UNIT (FIGURE 1):
Discharge pipe and suspension plate are deducted and a floor-stand base is
added. Available only for pit depths of 4'6" or less.
List price deduction, per pump, from the basic Figure 3 list prices shown
above --- $330
ALTERNATORS:
One (1) pedestal mounted alternating float switch on duplex units in lieu of
the two (2) standard float switches, ADD --- $108
One (1) pedestal mounted alternating float switch plus one (1) pedestal
mounted 2-pole auxiliary float switch on duplex units in lieu of the two (2)
standard float switches, ADD --- $936
PEDESTAL MOUNTED FLOAT SWITCHES:
In lieu of the standard motor mounted or suspension plate mounted float
switch, add per pump --- $195
OMISSION OF FLOAT SWITCH:
Omit float switch from basic pump and motor unit, deduct for each
pump --- $390
ADJUSTING COLLAR: Cast iron adjusting collar to fit around suspension leg
and permit field adjustment of pump length (Fig.3 pumps only, add per
pump --- $129
SPECIAL THRUST BEARING CONSTRUCTION: Standard VB-1/ units have solid
couplings and the thrust is absorbed by the motor bearing. A flexible coupling
and a ball thrust bearing in the motor pedestal can be furnished, if desired.
Add per pump --- $240
| OTHER MODIFICATIONS AND ACCESSORIES: |
| Magnetic starters and combination starters |
see Sec.4, VSA pages |
| Disconnect switches see |
see Sec.4, VSA pages |
| Starter modifications see |
see Sec.4, VSA pages |
| Export boxing list price addition |
2% of unit list price |
| Electric alternators |
see Sec.4, VSA pages |
| High water alarm switches and bells |
see Sec.4, VSA pages |
| NEMA-4 watertight float switch enclosures |
see Sec.8 |
| Explosion-proof float switch enclosures |
see Sec.8 |
| Stainless steel floats and rods |
see Sec.4, VSA pages |
| Mounting of controls |
see Sec.4, VSA pages |
| Panels (individual component enclosures) |
see Sec.4, VSA pages |
| Panels (single enclosure) |
see Sec.8 |
| Steel pit covers and covers plus grouting frames |
see Sec.4, VSA pages |
| Steel, cast iron and fiberglass basins |
see Sec.4, VSA pages |
| Grouting rings for basins |
see Sec.4, VSA pages |
| Galvanizing |
see Sec.4, VSA pages |
| Checkered steel covers and sectional covers |
see Sec.4, VSA pages |
| Totally enclosed and explosion-proof motors |
see Sec.8 |
